Output Options

Output Options allows you to assign individual outputs to activate for various events.

1. Go to Program > Output Options.

2. Program settings in Options, Energy Saving, and Outputs as needed. Refer to "Output Options Programming Reference" for details.

3. Select OK.

Output Options Programming Reference

The following reference provides basic descriptions of each field in Output Options. Configure each setting as needed.

Options

Cutoff Outputs (XR, XF6, XT, Com)

Enter outputs to turn off after the cutoff time. Range is 1-6.

Cutoff Time Minutes (XR, XF6, XT, Com)

Enter a number of minutes for outputs to remain on. Range is 1-99 minutes. Entering 0 results in continuous output. Default is 0 minutes.

Energy Saving

Heat Saver Temperature (XR, XT, XTL, Com)

Enter a temperature for Z-Wave thermostat (heating) when the system is armed All or Away. Range is 1-99 degrees. Enter 0 to disable this feature. Default is 0.

Cool Saver Temperature (XR, XT, XTL, Com)

Enter a temperature for Z-Wave thermostat (cooling) when the system is armed All or Away. Range is 1-99 degrees. Enter 0 to disable this feature. Default is 0.

Outputs

Communication Fail Output (XR, XF6, XT, XTL, Com)

Enter the output to turn on when communication fails. Enter 0 to disable this feature. Default is 0.

Fire Alarm Output (XR, DF6, XT, XTL)

Enter the output to turn on when a fire zone goes into alarm. Enter 0 to disable this feature. Default is 0.

Fire Trouble Output (XR, XF6, XT)

Enter the output to turn on when a fire zone reports trouble. Enter 0 to disable this feature. Default is 0.

Panic Alarm Output (XR, XT, XTL)

Enter the output to turn on when a panic zone goes into alarm. Enter 0 to disable this feature. Default is 0.

Ambush Output (XR, XT)

Enter the output to turn on when an ambush code is entered at the keypad. Enter 0 to disable this feature. Default is 0.

Entry Output (XR, XT, XTL)

Enter the output to turn on at the start of the entry delay time. Enter 0 to disable this feature. Default is 0.

Begin Exit Output (XR, XT, XTL)

Enter the output to turn on at the start of the exit delay time. Enter 0 to disable this feature. Default is 0.

End Exit Output (XR, XT, XTL)

Enter the output to turn on when an exit delay ends. Enter 0 to disable this feature. Default is 0.

Ready Output (XR, XT, XTL)

Enter the output to turn on when all disarmed burglary zones are in a normal state. Enter 0 to disable this feature. Default is 0.

Phone Trouble Output (XR)

Enter the output to turn on when phone trouble is reported. Enter 0 to disable this feature. Default is 0.

Late to Close Output (XR, XT)

Enter the output to turn on when a closing schedule expires. Enter 0 to disable this feature. Default is 0.

Device Fail Output (XR, XF6, XT75)

Enter the output to turn on when a device fails to respond to the panel. Enter 0 to disable this feature. Default is 0.

Armed Output (XT, XTL, Com)

Enter the output to turn on when the system is armed. Enter 0 to disable this feature. Default is 0.

Remote Arming Output (Com)

Enter the output to turn on when the system is armed from Virtual Keypad. Enter 0 to disable this feature. Default is 0.

Sensor Reset Output (XR, DF6, XT75)

Enter the output to turn on when a sensor reset is performed. Enter 0 to disable this feature. Default is 0.

Closing Wait Output (XR, XT75)

Enter the output to turn on when closing wait is initiated. Enter 0 to disable this feature. Default is 0.

Disarmed Output (XR, XT, XTL)

Enter the output to turn on when the system is disarmed. Enter 0 to disable this feature. Default is 0.

Burglary Output (XT, XTL)

Enter the output to turn on when a burglary zone goes into alarm. Enter 0 to disable this feature. Default is 0.

Arm-Alarm Output (XR, XT, XTL)

Enter the output to turn on when the system is armed. If the system goes into alarm, the output pulses. Enter 0 to disable this feature. Default is 0.

Supervisory Alarm Output (XR, XT75)

Enter the output to turn on when a supervisory zone goes into alarm. Enter 0 to disable this feature. Default is 0.

Home/Perimeter Output (XR, XT30/XT50)

Enter the output to turn on when a system is armed Home or Perimeter. Enter 0 to disable this feature. Default is 0.

All/Away Output (XR, XT30/XT50)

Enter the output to turn on when a system is armed All or Away. Enter 0 to disable this feature. Default is 0.

Sleep Output (XR, XT30/XT50)

Enter the output to turn on when a system is armed Sleep. Enter 0 to disable this feature. Default is 0.

Carbon Monoxide Output (XR, XF6, XT)

Enter the output to turn on when a carbon monoxide detector goes into alarm. Enter 0 to disable this feature. Default is 0.

Lockdown Output (XR, XT75)

Enter the output to turn on when a lockdown is initiated. Enter 0 to disable this feature. Default is 0.

Zone Monitor Output (XR, XT)

Enter the output to turn on when a zone monitor tone is activated on a keypad. Enter 0 to disable this feature. Default is 0.